[Linux-Biella] Souno a scatti quando c'è tanto carico di lavoro

[Daniele (Mastro)]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Daniele (Mastro) ha scritto:
> 
> hdparm /dev/hda
> 
> /dev/hda:
>  multcount    =  0 (off)
>  IO_support   =  0 (default 16-bit)
>  unmaskirq    =  0 (off)
>  using_dma    =  0 (off)
>  keepsettings =  0 (off)
>  readonly     =  0 (off)
>  readahead    = 256 (on)
>  geometry     = 16383/255/63, sectors = 156301488, start = 0


ok.. allora ecco qua il mio hard disk:

hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
        Model Number:       IC25N080ATMR04-0
        Serial Number:      MRA401K6K1D7HH
        Firmware Revision:  MO4OAD4A
Standards:
        Used: ATA/ATAPI-6 T13 1410D revision 3a
        Supported: 6 5 4
Configuration:
        Logical         max     current
        cylinders       16383   65535
        heads           16      1
        sectors/track   63      63
        --
        CHS current addressable sectors:    4128705
        LBA    user addressable sectors:  156301488
        LBA48  user addressable sectors:  156301488
        device size with M = 1024*1024:       76319 MBytes
        device size with M = 1000*1000:       80026 MBytes (80 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        Standby timer values: spec'd by Vendor, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 0
        Advanced power management level: 128 (0x80)
        Recommended acoustic management value: 128, current value: 254
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    SMART feature set
                Security Mode feature set
           *    Power Management feature set
           *    Write cache
           *    Look-ahead
           *    Host Protected Area feature set
           *    WRITE_BUFFER command
           *    READ_BUFFER command
           *    NOP cmd
           *    Advanced Power Management feature set
                Power-Up In Standby feature set
           *    SET_FEATURES required to spinup after power up
                Address Offset Reserved Area Boot
                SET_MAX security extension
                Automatic Acoustic Management feature set
           *    48-bit Address feature set
           *    Device Configuration Overlay feature set
           *    Mandatory FLUSH_CACHE
           *    FLUSH_CACHE_EXT
           *    SMART error logging
           *    SMART self-test
           *    General Purpose Logging feature set
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
                frozen
        not     expired: security count
        not     supported: enhanced erase
        66min for SECURITY ERASE UNIT.
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
Checksum: correct

direi che qui posso sapere cosa può fare e cosa no....
ora vorrei creare un settaggio ottimale....

continuo a leggere il man
il fatto è che so che se sbaglio son cazzi acidi!
e non ci tengo a sbagliare :D

- --
ciao,
Daniele
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

iD8DBQFFL+nzi33/AIKoeisRAiYbAJwIOX4mi8urAK4a/IhFZMU1Fa2zUACgmePE
ut6X1xJnpWL46/FEXtYvZaM=
=RNEG
-----END PGP SIGNATURE-----